Applications

3D printed anatomical models, orthoses and prosthetic covers

Hospital 3D-printing labs use FFF printers for patient-specific anatomical models, orthoses made from a limb scan and cosmetic covers for prostheses. This page walks through the workflow, the materials and why build volume matters, and states clearly what these models are not.

From CT or MRI to a printed model

The usual chain is: a CT or MRI study is exported as DICOM, segmentation software isolates the structure of interest (bone, a tumor, a vessel), the result is exported as an STL mesh, and a slicer prepares it for printing. Segmentation is the step that needs clinical judgment; the printer only reproduces what it is given. Keep patient identifiers out of file names and out of any shared folder, and follow your hospital's privacy rules.

Typical uses described by clinical teams: a craniofacial model to plan osteotomy lines and distractor positions and to route around an existing implant; an orbital-tumor model printed as two separate bodies, tumor and bone, so each can be handled alone; and full-size spine models of complex deformities to plan screw entry points and to orient during surgery, where a model may help reduce intraoperative imaging.

White 3D printed orbit and eye model from CT lying on printed surgical planning drawings
An orbital model printed from CT, checked against the planning drawings before surgery.

Why build volume matters

A full-size adult spine does not fit on a desktop printer without cutting it into sections that then have to be glued. Both the Epitum JL and the Epitum L offer 360 x 360 x 610 mm, so a spine can be printed upright in one piece. It takes time: in one project two full spine models took 64 and 98 hours. Plan overnight and weekend runs, and use the network queue rather than a person standing by.

Verification matters more than speed. Before a model is used in planning, a clinician should compare it with the source images, check a few landmark dimensions with calipers, and confirm the print has not lost thin walls or small foramina to the slicer. Record the scan date, segmentation settings, filament lot and print profile with each model, so that any question can be traced back later.

Enclosed anatomy and supports

Hollow structures such as sinuses, vessels or an orbit leave supports trapped inside, where tools cannot reach. The JL carries two nozzles in one print head, so one can print the model and the other a soluble support such as VXL111 or soluble PLA/PETG support, which dissolves in a bath. This also leaves cleaner surfaces than breakaway supports. The L, with a single nozzle, suits models where supports can be broken off.

Orthoses and prosthetic covers

In an orthotics workflow the clinician scans the limb with a 3D scanner or a phone or tablet, designs the device in orthotic software, and sends the job to the printer. Orthotic software exists that sends jobs to Epitum printers with one button. Printed designs cover finger, hand and forearm splints, arm orthoses with fixed or articulated elbows, and lower-limb orthoses. Vendor-quoted figures for the share of plaster casts replaced should be checked against your own case mix.

For prosthetics, one approach is to scan the healthy leg, model a cosmetic cover or a lamination form, and print it in ABS; thigh and lower-leg covers took about 32 hours on average in one clinic. Threaded inserts, soft elements and surface finishing are added by hand. A cover can be the final part or the mold for lamination. Materials that touch skin should come from a documented source: see medical-grade ABS and skin-contact polyolefin; use PC for stiffer, tougher frames.

UseMaterialWhy
Anatomical modelsMedical-grade ABSDocumented resin data, stable prints
Orthoses, skin contactSkin-contact polyolefinSoft feel, designed for skin
Rigid frames, coversPCTough, heat-resistant
Internal cavitiesVXL111Soluble support

Post-processing is modest: remove supports, sand contact edges, and add padding or straps where the design calls for them. Cleaning and any sterilization step are the clinic's decision; ABS does not survive steam autoclaving, so choose the material with that in mind.

Teaching aids

Models also serve residents, nursing programs and patient conversations: an enlarged joint, a hollow vessel tree, a procedural trainer, a mannequin part. Printing in house keeps cost per model low enough to give students something to hold. The JL is $9,899 and in stock in Orlando; the L is $8,299, made to order.

Disclaimer: what these models are not

Printed anatomical models are for planning, communication and teaching. They are not medical devices, do not replace imaging or clinical judgment, and carry no promise of any clinical outcome. A device that contacts a patient, such as an orthosis fitted to a person, is regulated in the United States by the FDA, and meeting those requirements is the clinic's responsibility. Your hospital's own procedures, quality system and legal review apply to every use described here.

Frequently asked questions

Are 3D printed anatomical models medical devices?

Models used for planning, communication and teaching are not medical devices, but where a printed item is used on or in a patient, FDA requirements apply and the clinic is responsible for meeting them. Check with your regulatory and legal teams before you use any model in a clinical setting.

How long does a full-size spine model take to print?

It depends on infill, layer height and orientation. In one project two models took 64 and 98 hours. A 360 x 360 x 610 mm build volume lets the spine print as one piece.

Which material should I use for an anatomical model?

Many labs use medical-grade ABS for models and a soluble support for enclosed anatomy. Biocompatibility data on the resin does not make a printed device biocompatible; see the material guide for what the certificates mean.

Can I make orthoses from a scan?

Yes, the workflow exists: scan the limb, design, print. Orthotic software can send jobs to Epitum printers with one button. Fitting and regulatory responsibility stay with the clinic.

Materials

Materials for this application

All material guides →

Applications

More applications

Automotive & motorsport

Master models for carbon-fiber layup, intake and air-box parts, trim and discontinued spares.

Investment casting

Printed wax and PMMA patterns for investment casting: metal parts from 1 to 50 pieces without pattern tooling.

Have a part in mind?

Send us the drawing or the STL, the load and the service temperature — we will suggest the material and the Epitum printer, and can print a sample in our Orlando showroom.

Talk to an engineer