Materials guide · Engineering

Medical-grade ABS filament: USP Class VI, ISO 10993 and printing

Medical-grade ABS is ABS made from a resin grade with biocompatibility test data and tighter change control. It is used for device housings, lab fixtures and anatomical models. This guide explains what the certificates mean, why they do not make a printed device biocompatible, and how to print and sterilize the material.

$67.53 ABS MED · 1 kg spool · USD
Order / Request a quote

What medical-grade ABS is — and when to choose it

Choose medical-grade ABS when a part goes into a medical device, a device prototype or a regulated lab and your quality file needs material biocompatibility data. Mechanically it is standard ABS; if the part must survive steam autoclaving, ABS is the wrong family.

USP <88> Class VI is a material screen. Extracts of the plastic in saline, alcohol-saline, polyethylene glycol 400 and vegetable oil (prepared at 50, 70 or 121 °C) go through systemic injection and intracutaneous tests, and the material itself through an implantation test. Passing says the resin showed no significant reactivity under those conditions — useful for raw-material selection, nothing more.

ISO 10993 evaluates the finished device. ISO 10993-1 (current edition 2025) is risk-based: the device maker classifies contact (surface, externally communicating, implant) and duration (up to 24 h, 24 h–30 days, over 30 days), then decides which endpoints — cytotoxicity, sensitization, irritation and more — need data. FDA's guidance on ISO 10993-1 states that it clears devices, not materials, and that the evaluation should cover processing, manufacturing and sterilization. Printing changes the material history — melt temperature, colorant, layer surface, cleaning — so a Class VI certificate does not make a printed part biocompatible. Responsibility stays with the device manufacturer.

Typical properties

PropertyTypical rangeTest method
Tensile strength (printed, XY)34–45 MPaISO 527 / ASTM D638
Tensile modulus1.5–2.4 GPaISO 527 / ASTM D638
Glass transition105–108 °CDSC
Vicat softening95–104 °CISO 306
Density1.04–1.06 g/cm³ISO 1183
Biocompatibility dataResin-level USP Class VI and/or ISO 10993Supplier certificate

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Typical print settings

Nozzle temperature235–270 °C
Build plate90–110 °C
ChamberClosed and heated, about 50–70 °C (Epitum: up to 90 °C)
Print speed30–60 mm/s
Part cooling0–25%
Drying70 °C · 2–6 h if exposed to humidity
NozzleClean, dedicated; ≥ 0.4 mm

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Lock the profile once parts pass verification: nozzle temperature, speed and lot number belong in the device history record, because a changed process can need a changed evaluation.

Which Epitum: JL or L

The Epitum L fits validated single-material production — one locked profile, one material, a heated chamber (up to 90 °C) against warping. The Epitum JL lets you reserve a nozzle for medical-grade ABS so it never sees other polymers; soluble supports such as VXL111 help with internal channels, but every support material and removal bath becomes part of your biological evaluation.

Applications

  • Housings and covers for diagnostic and monitoring equipment
  • Lab fixtures, sample holders and pipetting aids
  • Anatomical and surgical-planning models
  • Prototypes of handheld instruments and device enclosures

Troubleshooting and tips

  • No steam autoclave. ABS softens around 95–105 °C. In Stratasys' FDM sterilization study, ABS parts bent and fused in 121 °C autoclave cycles but showed no visible damage after EtO, hydrogen peroxide plasma or gamma.
  • Gamma with caution. Radiation can yellow ABS and reduce impact strength; validate at your dose.
  • Clean hot end. Purge or dedicate a nozzle; residue from other materials is uncontrolled.
  • Keep the paperwork. Record filament lot, profile and post-processing for every build.

Available from MG World Tech: ABS MED, 1 kg spool, $67.53. Order or request a quote →

Frequently asked questions

What is USP Class VI for plastics?

The most demanding class of USP <88> in vivo tests: systemic injection and intracutaneous tests with four extracts plus an implantation test. It screens a raw material; it is not a device clearance.

Does a USP Class VI filament make my printed device biocompatible?

No. FDA and ISO 10993-1 evaluate the finished device, including processing and sterilization. Material data supports the device maker's biological evaluation, which may still need testing of printed parts.

Can medical-grade ABS be autoclaved?

Steam autoclaving at 121–134 °C exceeds ABS's softening range and deforms parts. EtO and hydrogen peroxide plasma are the usual low-temperature routes; gamma works with possible yellowing and impact loss.

Is medical-grade ABS suitable for implants?

Not off the shelf. Filament makers that cite resin biocompatibility data commonly cap it at short-term contact — 30 days, topical, is a typical limit — so implants are outside what the material data supports. Check your grade's documentation.

Related guides

Keep reading

All material guides →

Order ABS MED or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote