Applications

Investment casting with 3D printed patterns

For a run of 1 to 50 castings, the pattern tooling often costs more than the metal. Printing the pattern in castable wax or PMMA removes the tool, and the foundry's shell, burnout and pour stay as they are. This guide covers when it pays, how wax and PMMA differ, the burnout workflow, and what to settle with your foundry first.

Why printed patterns replace pattern tooling

Conventional investment casting needs a mold to make each wax pattern. That mold is the expensive part of a small job: it has to be machined, and every design change means a new one. A printed pattern skips it. You send a CAD file to the printer, the pattern comes off the bed, and the foundry treats it like any other pattern: attach sprues, build the shell, remove the pattern, pour.

One foundry partner ran a trial batch of stainless-steel parts, 4 to 12 copies of each part, from printed patterns. The average came to about $12 per part, against about $1,800 for conventional pattern tooling for each part. In another project, a steel part for a pedal-assembly mechanism was quoted at about $6,000 for metal 3D printing; a printed wax pattern plus casting cost about $740. These are single projects with their own geometry and metal, not a price list, so ask your foundry to quote your part.

The manufacturer estimates that the whole casting cycle with printed patterns averages 10 to 12 times cheaper than milling and 8 to 9 times cheaper than metal 3D printing. Treat that as the manufacturer's estimate, not an independent measurement. The break-even depends on part size, alloy and how many pieces you need.

The same approach suits foundries making one-off replacement parts, industrial casting shops prototyping a new casting before cutting a mold, and engineers who need a handful of metal parts. At several hundred identical pieces, tooling usually wins again.

Wax or PMMA: which pattern material

Castable waxPMMA (acrylic)
How it leaves the shellMelts out at low temperature, then residue burns offBurns out in the furnace and leaves a hollow cavity
AshThe manufacturer lists below 0.01 %Low ash; confirm with a trial
SurfaceSmooth with a burner flame or solvent polishSmooth, precise; the clear material is easy to inspect
HandlingSofter and more brittle when cold; fits a wax-based shopLight and stiffer; not highly heat resistant
Best forLarge patterns, shops that already run a wax workflowPrecise detail, thin features, patterns that get handled a lot

Both materials have a full guide: castable wax and PMMA casting filament. Published datasheets for these filaments are thin, so a single test casting tells you more than any table. Keep the chamber heating off or low for both, because they soften well below the printer's 90 °C maximum.

A brass cast part next to the white 3D printed PMMA pattern it was cast from, on a wooden desk
A brass casting beside the printed PMMA pattern it was made from.

The PMMA burnout workflow in eight stages

One university research lab cast a brass engine for a model aircraft from a printed PMMA pattern. The sequence is the standard one, and it works the same for your parts:

  1. Print the PMMA master on a dual-extrusion printer, with support in a second material. The lab used HIPS dissolved in d-limonene.
  2. Dissolve the supports and prepare the master: clean it up and smooth the surface.
  3. Attach sprues made of burnout wax and set the pattern in the flask.
  4. Invest: fill the flask with gypsum investment around the pattern.
  5. Burn out in a furnace. The PMMA goes completely and leaves a hollow cavity.
  6. Pour the molten metal, brass in this case.
  7. Cool, break the shell and wash the gypsum out with a water jet.
  8. Cut the sprues, finish with abrasives and polish with a rotary tool.

With wax, stage 5 becomes a melt-out followed by burnout of the residue. Everything else is the same.

Design and print tips for burnout patterns

  • Walls. Keep walls as thin as the casting allows. Thick solid sections leave the most residue and are the hardest to burn out cleanly. Your foundry will tell you the minimum wall for the alloy.
  • Shell, not solid. Print a closed outer shell with sparse infill. It uses less material, burns out faster and leaves less ash. Leave a vent or drain hole where the shell traps air.
  • Sprue points. Attach sprues at thick sections and at the lowest point the metal will reach, and away from fine surface detail. Plan the attachment points in CAD; ask the foundry where it wants them.
  • Surface. Layer lines are copied into the metal. Use a fine layer height on visible faces, then smooth: a burner flame or solvent polish on wax, sanding and solvent smoothing on PMMA. Test on a scrap piece first, because solvents also soften small features.
  • Orientation. Place the best surface where it will not need support, and print with support only where the geometry demands it.
  • Storage. Keep patterns away from heat and sunlight, out of the way of anything that can scratch or bend them, and invest them soon after finishing. Wax in particular deforms in a warm room.

Which Epitum printer to use

For patterns with overhangs, internal channels or fine detail, the Epitum JL prints soluble or breakaway support from its second nozzle, so you can dissolve supports away instead of cutting them off the pattern. Pair PMMA with HIPS or use VXL111 where the support material suits your pattern material; check compatibility in the guides. For simple patterns that need no support, the Epitum L is enough. Both have a 360 × 360 × 610 mm volume, which holds several patterns or one large one. The JL is $9,899 and in stock in Orlando; the L is $8,299, made to order.

Limits to settle with your foundry

  • Shrinkage. The allowance for metal shrinkage comes from your foundry and the alloy, not from the printer. Apply it in CAD, and add any separate allowance for the pattern material if the foundry asks for one.
  • Burnout schedule. Temperature, ramp and hold depend on the shell system and the pattern material. Ask the foundry for its schedule and run a test casting before a production batch.
  • Foundry acceptance. Some shops do not accept printed patterns, or want a specific material. Ask before you print.
  • Size and detail. Very thin walls and sharp internal corners can fail in the shell regardless of how the pattern prints.

Frequently asked questions

Can I use a regular FFF printer for investment casting patterns?

You can print patterns on a capable FFF printer, but the material matters: use castable wax or PMMA made for burnout, and confirm with your foundry. A second nozzle helps when the pattern needs support.

How many castings make printed patterns worthwhile?

Usually from one piece up to a few dozen. Tooling often costs more than the metal in that range. At hundreds of identical parts, conventional tooling tends to win.

Is wax or PMMA better for burnout?

Wax fits shops with a wax workflow and large patterns. PMMA gives precise, smooth patterns that are easy to handle. See the wax guide and the PMMA guide, and test both with your foundry.

Who sets the shrinkage allowance?

Your foundry. It depends on the alloy and the shell process. Ask for the figure before you finish the CAD model.

Materials

Materials for this application

All material guides →

Applications

More applications

Automotive & motorsport

Master models for carbon-fiber layup, intake and air-box parts, trim and discontinued spares.

Have a part in mind?

Send us the drawing or the STL, the load and the service temperature — we will suggest the material and the Epitum printer, and can print a sample in our Orlando showroom.

Talk to an engineer