Materials guide · Support

Soluble support filament for nylon, PC and ABS

Breakaway support leaves scars and cannot reach internal channels. Soluble support can — but the familiar PVA was made for PLA. This guide compares the support types that survive engineering-plastic temperatures and how to print and dissolve them.

$247.50 VXL111 · 0.75 kg spool · USD
Order / Request a quote

Which soluble support for engineering plastics

A support has to stay rigid in the chamber the model needs, bond to the model and still dissolve. Low-temperature PVA softens near 60 °C; at least one maker lists it as unsuitable for ABS, PC and PP. BVOH bonds to more materials but is still a low-temperature support.

For engineering work there are three practical routes. High-temperature water-soluble grades tolerate chambers around 120 °C and dissolve in hot water; versions for PEEK, PEKK and PEI target chambers far hotter than the 90 °C an Epitum provides. Removal-agent soluble copolymers dissolve in a heated alkaline bath, which makes them less moisture-sensitive than PVA. HIPS dissolves in d-limonene and pairs with ABS — see the HIPS guide.

The catalog support offered here is listed for ABS, ASA, HIPS, PA, PC and PPS, and is removed in a water bath with a removal agent, not in plain water.

Typical properties by support type

Support typeRemoved withTypical model materials · chamber
PVAWaterPLA, PETG, nylon · cool chamber (Tg ≈ 58–60 °C)
BVOHWater, even coldPLA, PETG, ABS, ASA, TPU · low-temperature
High-temperature water-solubleHot water, 70–80 °CABS, PA, PC, PC/ABS, PP, TPU · up to ≈ 120 °C
Removal-agent soluble copolymerHeated alkaline bathABS, ASA, PC-class · per grade
HIPSd-LimoneneABS · ABS-like chamber

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Typical print settings

Nozzle temperature220–250 °C for high-temperature and removal-agent grades
Build plateSet for the model material (support grades tolerate up to ≈ 130 °C)
ChamberAs the model needs, below the support’s limit (Epitum: up to 90 °C)
InterfaceZ gap 0 mm; 2–4 dense interface layers
Print speed30–50 mm/s for support
Drying70–80 °C if the support has absorbed moisture
StorageSealed with desiccant; dry box while printing

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Many users print only the interface in soluble material and the bulk support in the model material: it saves support filament and dissolving time.

Why it needs the Epitum JL

Soluble support needs a second nozzle, so the single-extruder Epitum L cannot print it. The Epitum JL runs model and support from two nozzles with JetSmart™ switching in under 0.5 s. A mechanical valve seals the idle nozzle, so it does not ooze onto the part and no wipe tower is printed. The chamber, heated up to 90 °C, stays below the ≈ 120 °C limit of high-temperature water-soluble grades — check the limit of any other grade — and the 430 °C hot end covers PA, PC and PPS-CF.

Dissolving workflow

  1. Let the part cool, then pull off bulk support by hand where it is safe.
  2. Soak in a heated, stirred bath; agitation shortens times considerably.
  3. Keep the bath below the model’s softening point, especially for ABS.
  4. Rinse, then dry; nylon parts absorb water in the bath.
  5. Dispose of the spent bath according to local wastewater rules.

Applications

  • Nylon and carbon-fiber nylon manifolds with internal channels
  • PC housings with internal bosses and undercuts
  • Print-in-place mechanisms and lattices

Troubleshooting and tips

  • Support sags or curls: chamber too hot for that support type.
  • Interface peels mid-print: dry the support and lower the interface speed.
  • Stringing from support: wet filament. Store sealed with desiccant and feed from a dry box.
  • Slow dissolving: heat and stir the bath; replace a saturated bath.

Available from MG World Tech: VXL111, 0.75 kg spool, $247.50; VXL EX 1000g, 1 kg spool, $73.15. Order or request a quote →

Frequently asked questions

Can you use PVA support with nylon or polycarbonate?

PVA can work with nylon, but it softens near 60 °C and at least one manufacturer lists it as unsuitable for ABS and PC. For hot chambers use a high-temperature water-soluble or a removal-agent soluble support.

What is the difference between water-soluble and removal-agent supports?

Water-soluble supports (PVA, BVOH, high-temperature grades) dissolve in water. Removal-agent supports dissolve in a heated bath of water mixed with an alkaline agent and are less sensitive to moisture.

What Z distance should soluble support use?

Zero. Nothing has to be broken off, so the interface is printed directly against the model, which gives clean downward-facing surfaces.

Can a single-extruder printer print soluble support?

No — support and model must come from separate nozzles. On Epitum that means the dual-extrusion Epitum JL.

Related guides

Keep reading

All material guides →

Order VXL111 or VXL EX 1000g or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote