Materials guide · Engineering

Skin-contact polyolefin filament for orthoses, splints and wearables

Polypropylene has been the workhorse of thermoformed orthoses for decades. Skin-contact polyolefin filaments bring that material family to 3D printing, with test data for contact with intact skin. This guide explains what such data covers, what stays with the device maker, and how to print polyolefins without fighting warp.

$93.54 Healthfil FORTIS · 0.75 kg spool · USD
Order / Request a quote

What a skin-contact polyolefin is — and when to choose it

Polyolefins — polypropylene, polyethylene and their blends — are light, tough, fatigue-resistant and inert to sweat, soap and disinfectants. Choose a skin-contact grade over ordinary PP when the printed part will sit on a patient's or wearer's skin and your quality file needs material data. For device housings and lab parts that need stiffness rather than flexibility, medical-grade ABS is the neighbor.

“Skin-contact certified” usually means test specimens passed the three endpoints FDA and ISO 10993-1 associate with intact-skin surface devices: cytotoxicity (ISO 10993-5, in vitro), sensitization (ISO 10993-10) and irritation (ISO 10993-23, split out of -10 in 2021; older reports cite -10). FDA's ISO 10993-1 guidance goes further for intact skin: polypropylene and polyethylene are on its list of materials where a device maker may document materials instead of submitting test reports — although some cases, such as devices for neonates, call for discussion with FDA first.

None of this transfers to your part automatically. Results describe the specimen tested; printing parameters, colorants, cleaning and finishing are yours. The device manufacturer owns the biological evaluation of the finished device.

Typical properties

PropertyTypical rangeTest method
Tensile strength (printed, XY)10–16 MPaISO 527 / ASTM D3039
Elongation at break (XY)Over 100% (grade-dependent)ISO 527
Heat deflection, 0.45 MPa54–65 °CISO 75
Melting point130–165 °CDSC
Density0.89–0.91 g/cm³ISO 1183
Skin-contact dataCytotoxicity, sensitization, irritationISO 10993-5 / -10 / -23

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Typical print settings

Nozzle temperature200–240 °C
Build plate50–100 °C on PP sheet or PP tape
ChamberClosed, warm; one maker recommends 65–80 °C (Epitum: up to 90 °C)
Print speed20–50 mm/s
Part cooling0–50%
Drying60–70 °C · 4–24 h if exposed to humidity
NozzleClean, dedicated; ≥ 0.4 mm

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Print a test coupon on your bed surface first: polyolefins bond only to polyolefins, so a PP sheet or PP tape is the foundation. Too hot a bed can weld the part to a PP sheet.

Which Epitum: JL or L

The Epitum L fits clinics and labs printing one material: its chamber, heated up to 90 °C, covers the warm build space polyolefins like, and 360 × 360 × 610 mm takes full-length leg orthoses. The Epitum JL keeps one nozzle dedicated to the skin-contact grade while the other runs other jobs. Expect moderate speeds, far below the 500 mm/s travel peak.

Applications

  • Custom wrist, hand and finger splints
  • Ankle-foot and other orthoses, from prototypes to fitted devices
  • Cosmetic covers and padding shells for prostheses
  • Wearable housings, straps and sports protective inserts

Troubleshooting and tips

  • Warping on long parts. Close and heat the chamber, add a wide brim and avoid sharp corners.
  • Rough edges. Smooth trim lines and strap slots; edges, not material, cause most skin complaints.
  • Heat. Polyolefins deflect around 55–65 °C under light load, so steam sterilization and hot-car storage can distort parts.
  • Keep it clean. No bed adhesives or coatings on skin-contact faces unless they are part of your evaluation.

Available from MG World Tech: Healthfil FORTIS, 0.75 kg spool, $93.54. Order or request a quote →

Frequently asked questions

What does skin-contact certified filament mean?

Test specimens of the filament passed cytotoxicity (ISO 10993-5), sensitization (ISO 10993-10) and usually irritation (ISO 10993-23) tests. It describes the material, not your finished device.

Is polypropylene safe for skin contact?

PP has a long history in orthoses and is on FDA's list of low-risk materials for devices contacting only intact skin. Additives, colorants and processing still matter, so use a grade with test data.

Do I still need a biocompatibility evaluation for a printed orthosis?

Yes — the device maker evaluates the finished device under ISO 10993-1 and the applicable regulations. Material data and FDA's intact-skin approach can reduce, not remove, that work.

Why does polypropylene filament warp?

Polyolefins shrink as they crystallize. A closed, warm chamber, a PP bed surface and a brim keep parts flat; fiber-filled PP-CF warps much less but is too stiff for most skin-contact parts.

Related guides

Keep reading

All material guides →

Order Healthfil FORTIS or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote