Materials guide · Composites

PA12 carbon fiber filament: print settings and properties

PA12-CF is nylon 12 filled with chopped carbon fiber — a stiff, light, tough composite that holds its properties in humid air far better than carbon-fiber PA6. Here are the typical published values and a starting profile for an industrial printer.

$113.95 PA12 CF 15 · 0.75 kg spool · USD
Order / Request a quote

What PA12-CF is — and why nylon 12

All nylons absorb water, and water plasticizes them: a PA6 part that is stiff off the printer can lose a large share of its modulus once it reaches equilibrium with humid air. Nylon 12 has a longer hydrocarbon chain and fewer amide groups per unit length, so it takes up much less water. One manufacturer's data illustrate the gap: its PA12-CF levels off at about 1.5 % water in humid air, versus 3.3 % for its PA6-CF.

That is the reason to pick PA12-CF: predictable dimensions and stiffness in a shop, a vehicle or outdoors, with easier spool handling. Its melting point (about 170–180 °C) and heat deflection are lower than PA6's, and its dry stiffness is usually lower than a high-fiber PA6 grade. If you need maximum dry stiffness for metal-replacement parts, compare our PA-CF guide.

Typical properties

PropertyTypical range (dry)Test method
Fiber content≈ 10–15 % carbon fiber (by weight)—
Tensile strength, XY77–125 MPaISO 527
Tensile modulus, XY3.3–8.0 GPaISO 527
Tensile strength, Z (layer bond)≈ 50 MPa (one published value)ISO 527
Elongation at break, XY4–5 %ISO 527
Charpy impact, notched10–15 kJ/m²ISO 179
Heat deflection, 0.45 MPa130–170 °CISO 75
Heat deflection, 1.8 MPa105–150 °CISO 75
Melting temperature≈ 170–180 °CDSC
Water absorption≈ 1–1.5 % at equilibrium (PA6-CF: ≈ 2.3–3.3 %)Equilibrium, humid air
Density1.06–1.07 g/cm³ISO 1183

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Dry vs. conditioned. Datasheets for nylons quote "dry" (as printed or freshly dried) and "wet" or "conditioned" values. In one published PA12-CF dataset, tensile strength drops only about 7 % and modulus about 5 % after a hot-water soak, while the same maker's PA6-CF loses roughly half its strength and most of its modulus under the same treatment. Design PA12-CF to its conditioned values, but expect a much smaller gap.

Typical print settings

Nozzle temperature255–300 °C
Build plate80–110 °C, glue or PA adhesive on PEI (some low-warp grades: 40–50 °C)
ChamberNot required; a closed, warm chamber helps large parts (Epitum: up to 90 °C)
Print speedTypically 40–100 mm/s
Part cooling0–10 %
Drying80–100 °C · 4–10 h
NozzleHardened steel or ruby, ≥ 0.4 mm

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Start near 270 °C and 50 mm/s with the fan almost off. Stringing usually means wet filament rather than too much heat; dry the spool before lowering the temperature. Some low-warp grades are formulated for a 40–50 °C bed — follow your spool's datasheet when it differs from the typical range.

Which Epitum: JL or L

Epitum L suits single-material production of jigs, fixtures, gripper fingers and brackets: a 430 °C hot end is far more than PA12-CF needs, the 90 °C heated chamber helps keep long, flat tools from curling, and the end-of-filament sensor pauses an overnight job instead of ruining it when a spool runs out.

The Epitum JL adds a second nozzle with a mechanical blocking valve. Use it for soluble support — VXL111 lists PA among its partner materials — under ducts, manifolds and deep overhangs, or run the composite in one nozzle and a different material in the other. Epitum nozzles are wear-resistant as standard, so no swap is needed for carbon fiber.

Applications

  • Assembly jigs, fixtures and inspection gauges that must hold size through seasonal humidity
  • End-of-arm tooling and robot gripper fingers
  • Drone and robotics brackets, arms and enclosures where mass matters
  • Parts exposed to oils, greases and fuels in automotive and machinery service

Troubleshooting and tips

  • Dry anyway. Lower moisture uptake does not mean none; an opened spool left in shop air still pops and prints weaker. Feed from a dry box on long jobs.
  • Use a hardened nozzle. Carbon fiber wears brass nozzles quickly; hardened steel or another wear-resistant nozzle of 0.4 mm or larger keeps line width stable.
  • Avoid very fine layers. Below about 0.2 mm, fiber-filled filament tends to under-extrude and clog; about 60 % of nozzle diameter is a sound starting layer height.
  • Anneal if you need the datasheet numbers. Several manufacturers test after an anneal (for example 100 °C for 16 h); annealing also dries the part, so let it re-condition before measuring.
  • Use an adhesive for the first layer. A thin glue layer on PEI is common for PA; nylon can bond to bare PEI hard enough to damage the sheet.

Available from MG World Tech: PA12 CF 15, 0.75 kg spool, $113.95. Order or request a quote →

Frequently asked questions

What is the difference between PA12-CF and PA6-CF?

PA6-CF is usually stiffer and more heat-resistant when dry. PA12-CF absorbs roughly half as much water or less, so its stiffness and dimensions change far less in humid air. Pick PA12-CF for parts that live in uncontrolled humidity; see our PA-CF guide for high-fiber PA6 grades.

What temperature do you print PA12 carbon fiber at?

Typically 255–300 °C at the nozzle, an 80–110 °C bed with an adhesive, and the fan almost off. Grades differ, so start from your spool's datasheet and the Printoformer profile.

Does PA12-CF need to be dried?

Yes, before printing if the spool has been open: typically 80–100 °C for 4–10 hours. PA12 absorbs moisture more slowly than PA6, but wet filament still strings, bubbles and loses strength.

Is PA12 carbon fiber strong enough to replace aluminum?

For lightly loaded brackets, fixtures and tooling, often yes, at less than half the weight. Printed PA12-CF is far weaker than aluminum in absolute terms and weaker across layers, so check the load case first.

Related guides

Keep reading

All material guides →

Order PA12 CF 15 or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote