Materials guide · Basic

HIPS filament: settings, and HIPS as support for ABS

High-impact polystyrene (HIPS) is a light, easy-to-finish plastic in its own right, but most engineers meet it as the support material for ABS: it prints at the same temperatures and dissolves in d-limonene, which leaves ABS intact. This guide covers both uses and is honest about the solvent.

$50.19 HIPS · 1 kg spool · USD
Order / Request a quote

What HIPS is — and when to choose it

HIPS is polystyrene toughened with a dispersed rubber phase. It is lighter and somewhat less stiff and heat-resistant than ABS, sands and paints easily, and has very low moisture uptake. As a part material it suits display models, packaging prototypes and light covers.

Its bigger role is support. HIPS prints in the same temperature window as ABS, bonds to it well enough to hold overhangs, and dissolves in d-limonene, a citrus-derived solvent that dissolves polystyrene without harming the ABS part. It can also be used as a breakaway support for ABS and ASA.

Typical properties

PropertyTypical rangeTest method
Density1.04–1.05 g/cm³ISO 1183
Tensile strength27–40 MPaISO 527
Tensile modulus1.2–1.35 GPaISO 527
Elongation at break13–18 % printed (one sheet lists 64 %)ISO 527
Flexural modulus≈ 1.6 GPaISO 178
Heat deflection, 0.45 MPa79–80 °CISO 75
Glass transition≈ 100 °CDSC
Solubilityd-limonene; not water—

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Typical print settings

Nozzle temperature225–240 °C
Build plate90–110 °C (80–115 °C published)
ChamberClosed; warm when paired with ABS (Epitum: up to 90 °C)
Print speedMatch the ABS it supports; slow first layer
Part coolingOff to low
DryingRarely needed (low moisture uptake); if wet, ABS-type drying
NozzleBrass, ≥ 0.4 mm

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

When HIPS supports ABS, run both at ABS-like conditions: one bed temperature that suits both, the chamber closed and warm, and a support interface with zero top gap so HIPS and ABS fuse. HIPS shrinks and warps much like ABS, so large standalone parts need the same brim and chamber discipline — see the first-layer adhesion guide.

Dissolving HIPS supports in limonene

d-limonene works, but it is a real industrial solvent. Typical safety data sheets classify it as a flammable liquid (flash point around 45–48 °C), a skin irritant and sensitizer, an aspiration hazard if swallowed, and very toxic to aquatic life.

  • Ventilate and keep it cool. Use a lidded container in a ventilated area away from ignition sources; do not heat the bath.
  • Protect skin. Wear chemical-resistant gloves and eye protection.
  • Expect hours, not minutes. Break away bulk support first; agitation speeds dissolution.
  • Dispose of it properly. Spent limonene is chemical waste, never a drain liquid.
  • Rinse and dry the part before measuring or assembly.

If a flammable solvent bath does not fit your shop, a dedicated soluble support for engineering plastics is removed in a water bath with a removal agent instead.

Which Epitum: JL or L

For HIPS as support you need the Epitum JL ($9,899): ABS in one nozzle, HIPS in the other. JetSmart™ seals the idle nozzle with a mechanical valve and switches in under 0.5 s with no wipe tower, so there is no oozing of one material into the other. The heated chamber (up to 90 °C) keeps both materials warm on tall builds.

For HIPS parts alone, the single-extruder Epitum L ($8,299) is enough.

Applications

  • Soluble or breakaway support for ABS: internal channels, enclosed cavities, deep overhangs
  • Display models, packaging and point-of-sale prototypes
  • Lightweight covers and parts to be sanded and painted

Troubleshooting and tips

  • Supports fall off mid-print. Reduce the support-to-part gap and raise the interface temperature slightly.
  • Rough supported faces. Normal on the side that touched support; orient cosmetic faces away from supports.
  • Bath slows down. Saturated limonene dissolves slowly; replace it.

Available from MG World Tech: HIPS, 1 kg spool, $50.19. Order or request a quote →

Frequently asked questions

Is HIPS soluble in water?

No. HIPS dissolves in d-limonene. If you need water-based removal, use a dedicated soluble support with a removal-agent bath, such as the one in our soluble support guide.

Does limonene damage ABS?

ABS is generally unaffected when HIPS supports are dissolved in d-limonene, which is why the pair is used. Take the part out once supports are gone and rinse it.

Is d-limonene safe to use?

It needs normal solvent precautions: it is flammable (flash point around 45–48 °C), can irritate and sensitize skin, and is toxic to aquatic life. Ventilate, wear gloves, keep it cool and dispose of it as chemical waste.

What materials can HIPS support?

HIPS is matched to ABS, and at least one manufacturer also lists it as breakaway support for ASA. For PLA and PETG, a support designed for them is the safer choice — see the PLA/PETG soluble support guide.

Related guides

Keep reading

All material guides →

Order HIPS or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote