What “food-safe ABS” means — and when to choose it
Choose food-contact ABS when a printed part touches food or a food-contact surface and you need ABS stiffness and toughness. Standard ABS prints the same way but has no food-contact paperwork; polypropylene is the usual alternative for wet, chemically cleaned service.
In the EU, Regulation (EC) 1935/2004 is the framework: materials must not transfer constituents to food in amounts that endanger health or change its composition, taste or odor. Regulation (EC) 2023/2006 requires good manufacturing practice along the chain. Regulation (EU) 10/2011 covers plastics: only substances on its Union list may be used, total migration may not exceed 10 mg/dm² (overall migration limit), listed substances have specific migration limits, and testing uses food simulants — 10% ethanol (A), 3% acetic acid (B), 20% ethanol (C), 50% ethanol (D1), vegetable oil (D2). Each business in the chain passes on a written declaration of compliance that states the conditions of use it covers.
In the US, FDA does not approve filaments. ABS is addressed in 21 CFR: § 181.32 (prior sanction) allows ABS with less than 30% acrylonitrile as piping and repeated-use articles, with acrylonitrile extraction limits; § 177.1020 describes a specific high-acrylonitrile ABS. Colorants and additives need their own clearance, and new substances go through the Food Contact Notification program. Compliance belongs to the finished article under its real conditions of use — verify your application with a compliance specialist; this guide is not legal advice.
Typical properties
| Property | Typical range | Test method |
|---|---|---|
| Tensile strength (printed, XY) | 34–47 MPa | ISO 527 |
| Tensile modulus | 1.5–2.4 GPa | ISO 527 |
| Glass transition | 105–108 °C | DSC |
| Vicat softening | 95–104 °C | ISO 306 |
| Density | 1.03–1.06 g/cm³ | ISO 1183 |
| Food-contact basis | Declaration of compliance per grade and color | EU 10/2011 / 21 CFR |
Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).
Typical print settings
| Nozzle temperature | 235–265 °C |
|---|---|
| Build plate | 90–110 °C |
| Chamber | Closed and heated, about 50–70 °C (Epitum: up to 90 °C) |
| Print speed | 30–80 mm/s |
| Part cooling | 0–25% |
| Drying | 70 °C · 2–6 h if exposed to humidity |
| Nozzle | Clean, dedicated to food-contact work; ≥ 0.2 mm |
Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.
Dial in on a test coupon, then print contact faces with more perimeters and finer layers. Dense walls matter more than infill: crevices between beads are where residue and bacteria collect.
Which Epitum: JL or L
The Epitum L suits single-material food tooling; its heated chamber (up to 90 °C) and 360 × 360 × 610 mm volume handle long guide rails in one piece. The Epitum JL lets you dedicate one nozzle to food-contact ABS so it never carries residue from other materials. Avoid dissimilar or soluble supports on contact faces. Expect ABS to print well below the 500 mm/s travel peak.
Applications
- Guide rails, star wheels and change parts on packaging lines
- Portioning, dosing and sorting fixtures
- Dispenser and container prototypes for design validation
- Custom tooling for bakeries, confectionery and food-service equipment
Troubleshooting and tips
- Dedicated, clean hot end. Purge thoroughly or reserve a nozzle. Brass often contains some lead, so many shops use a stainless-steel nozzle for food-contact work.
- No adhesives on contact faces. Bed glue, release sprays and post-print coatings are not covered by the filament's declaration.
- Mind heat. ABS softens near 95–105 °C; commercial hot-water sanitizing rinses run around 82 °C (180 °F), so test parts through real cycles first.
- Warping. Close the chamber and heat it; ABS shrinks and lifts at corners.
- Inspect and replace. Treat printed contact parts as wear items: cracks and scratches hold residue.
Available from MG World Tech: ABS FOOD, 1 kg spool, $67.53. Order or request a quote →
Frequently asked questions
Is ABS filament food safe?
Only a grade with a declaration of compliance for food contact, used within the conditions it states (food type, time, temperature). Ordinary ABS has no such paperwork, and colorants change the picture: some suppliers cover only the natural or white grade.
Is food-contact ABS FDA approved?
FDA does not approve filaments. ABS is addressed in 21 CFR (for example § 181.32 for repeated-use articles), and compliance is judged for the finished article under its conditions of use. An EU declaration of compliance is a separate document.
Can food-contact ABS parts go in a dishwasher?
Test first. ABS softens near 95–105 °C, and hot sanitizing rinses can warp thin printed parts. For hotter wash cycles evaluate a higher-temperature material such as polycarbonate — again with its own food-contact documentation.
Are 3D printed parts safe for food contact?
The filament is only half of it. Layer crevices trap residue, so print dense, smooth contact faces, use a clean dedicated nozzle, avoid adhesives, and clean and replace parts on a schedule.