Materials guide · Composites

Carbon-fiber ABS (ABS-CF): print settings and when to use it

Chopped carbon fiber turns ABS into a stiffer, dimensionally steadier material with a matte finish and much less warping. The price is lower elongation and an abrasive filament. Here are typical settings across manufacturers and what to expect from printed parts.

$74.92 ABS CF · 0.75 kg spool · USD
Order / Request a quote

What carbon-fiber ABS is — and when to choose it

ABS-CF is ABS compounded with short chopped carbon fibers, typically 10–20% by weight. The fibers stiffen the part, cut thermal expansion along the print direction, and give a matte surface that hides layer lines. One FDM manufacturer rates its 10% grade at about 50% stiffer and 15% stronger than its standard ABS.

The trade-off is toughness: elongation at break drops to a few percent, so ABS-CF parts are stiff but less forgiving of impacts and snap-fits. Choose it for fixtures, brackets and housings that must stay flat and rigid. If you need more heat or chemical resistance, step up to carbon-fiber nylon 12; if the part must be static-dissipative, use ESD-safe ABS — carbon-fiber ABS is not ESD-rated by default.

Typical properties

PropertyTypical rangeTest method
Density1.03–1.11 g/cm³ISO 1183 / ASTM D792
Tensile strength, printed37–46 MPaISO 527 / ASTM D638
Tensile modulus, printed2.2–5.2 GPaISO 527 / ASTM D638
Elongation at break2–3 %ISO 527 / ASTM D638
Flexural strength57–76 MPaISO 178 / ASTM D790
Heat deflection76–113 °C (wide spread between sheets)ISO 75 / ASTM D648
Glass transition100–105 °CDSC
CTE, in plane vs across layers≈ 19 vs ≈ 76 µm/m·°C (one sheet)ASTM E831
Surface resistance> 10⁹ Ω — not ESD-dissipativeASTM D257

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

The spread in stiffness is real: fiber content, fiber length and the base resin differ between products, so the modulus of your spool can sit anywhere in that range.

Typical print settings

Nozzle temperature220–260 °C
Build plate100–110 °C
ChamberClosed and heated recommended (Epitum: up to 90 °C)
Print speed≈ 50 mm/s starting point; raise gradually
Part coolingOff to low
Drying≈ 80 °C · 4 h
NozzleHardened steel or ruby, ≥ 0.4 mm (0.6 mm preferred)

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Manufacturers advise against very fine layers with fiber-filled filament — fibers bridge narrow passages and can clog small nozzles. Start around 0.2 mm layers on a 0.4–0.6 mm nozzle and keep the chamber closed; ABS-CF warps far less than plain ABS, but a warm chamber still improves layer bonding.

Which Epitum: JL or L

The Epitum L ($8,299) is the natural fit for single-material ABS-CF fixtures and tooling: the heated chamber (up to 90 °C), the 360 × 360 × 610 mm volume for long, flat parts, and an end-of-filament sensor that pauses a long job instead of ruining it.

The Epitum JL ($9,899) adds a second nozzle. It can carry a soluble support for internal channels and enclosed cavities, or carry a second material. Epitum nozzles are wear-resistant as standard; on other printers, fit a hardened nozzle before running carbon fiber.

Applications

  • Assembly jigs, drilling and bonding fixtures, check gauges
  • Robot end-of-arm tooling and lightweight brackets
  • Drone and vehicle housings that must stay flat
  • Functional prototypes with a molded-looking matte finish

Troubleshooting and tips

  • Underextrusion after a few spools. A worn brass nozzle widens and loses flow accuracy; use hardened steel or ruby-tipped nozzles and check them regularly.
  • Clogs. Use 0.4 mm as the minimum (some makers recommend 0.6 mm) and avoid layers far below 0.2 mm.
  • Brittle snap-fits. Expected with 2–3% elongation; redesign clips with longer beams or use plain ABS for flexing features.
  • Weak layers. Dry the spool, raise nozzle temperature 5–10 °C, close the chamber.

Available from MG World Tech: ABS CF, 0.75 kg spool, $74.92. Order or request a quote →

Frequently asked questions

Do I need a hardened nozzle for carbon fiber ABS?

Yes. Carbon fiber is abrasive and wears brass nozzles, which then widen and underextrude. Manufacturers recommend hardened steel or ruby-tipped nozzles of at least 0.4 mm; some specify 0.6 mm.

Is carbon fiber ABS stronger than ABS?

It is stiffer and usually somewhat stronger in tension, but less tough: elongation at break falls to about 2–3%. Use it where rigidity and flatness matter more than impact absorption.

Does carbon fiber ABS warp less?

Yes. The fibers cut thermal expansion along the print direction, so large flat parts lift much less. A closed, warm chamber is still recommended.

Is carbon fiber ABS ESD safe?

Not by default. Published surface resistance for standard ABS-CF is above 10⁹ Ω. For static-sensitive electronics use a purpose-made ESD-safe ABS and measure the printed part.

Related guides

Keep reading

All material guides →

Order ABS CF or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote