Materials guide · Engineering

ESD-safe ABS: resistance classes, measurement and print settings

ESD-safe ABS carries a conductive filler that lets static charge bleed away in a controlled way, so printed trays, nests and fixtures can be used around sensitive electronics. This guide explains the resistance classes, why a printed part has to be measured rather than assumed, and the typical settings across manufacturers.

$113.06 ABS ESD · 0.75 kg spool · USD
Order / Request a quote

What ESD-safe ABS is — and the resistance classes

Ordinary ABS is an insulator: published surface resistance for unfilled grades is above 10¹³ Ω, so charge stays where friction puts it. ESD grades add a conductive filler — typically carbon-based, such as carbon nanotubes — to bring resistance into a controlled range. The ESD Association defines the classes by surface or volume resistance:

  • Conductive: below 1 × 10⁴ Ω — charge moves fast, which can itself cause a sharp discharge.
  • Static dissipative: 1 × 10⁴ to below 1 × 10¹¹ Ω — charge drains to ground in a controlled way. This is the usual target for fixtures that touch devices.
  • Insulative: 1 × 10¹¹ Ω and above.

"Antistatic" is not a resistance class: in ESD Association usage it describes low charge generation, and a material's low-charging behavior is not predicted by its resistance. Product names use the word loosely, so always read the resistance value on the spool's datasheet.

Within a factory, these materials sit inside an ESD control program. ANSI/ESD S20.20 sets the requirements for handling items that can be damaged by 100 V HBM, 200 V CDM or 35 V on isolated conductors; conductive or dissipative fixtures in the protected area are grounded as part of that program.

Typical properties

PropertyTypical rangeTest method
Surface resistance, printed10⁴–10⁹ Ω (most grades 10⁷–10⁹)ASTM D257 / ANSI/ESD STM11.11
Density0.97–1.09 g/cm³ISO 1183
Tensile strength, printed24–58 MPaISO 527 / ASTM D638
Tensile modulus1.1–2.7 GPaISO 527 / ASTM D638
Elongation at break2–6 %ISO 527 / ASTM D638
Heat deflection, 0.45 MPa96–105 °CISO 75 / ASTM D648
Glass transition105–107 °CDSC

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Typical print settings

Nozzle temperature220–280 °C — follow your spool; temperature also shifts resistance
Build plate90–110 °C
ChamberClosed, heated recommended (Epitum: up to 90 °C)
Print speedModerate — 40 mm/s test-specimen speed; some grades allow more
Part coolingOff to 40 %
Drying≈ 80–85 °C · 8 h
Nozzle≥ 0.4 mm; hardened if the datasheet calls the filler abrasive

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Measure every new part design. Resistance of a printed part is not a fixed property of the spool. One manufacturer reports that higher nozzle temperatures make its ESD ABS more conductive and lower ones less, and recommends dialing resistance in with temperature. Another found that orientation and wall thickness shift readings, with the most scatter in thin-walled cylinders, and supports touching a wall can disturb its surface resistance. Measure finished parts with a calibrated resistance meter at the contact points that matter, and re-check after any change in settings, nozzle or spool lot.

Which Epitum: JL or L

The Epitum L ($8,299) suits most ESD work: trays, nests, test-fixture plates and pick-and-place parts in one material, with the heated chamber (up to 90 °C) keeping large flat plates true.

The Epitum JL ($9,899) helps when a part needs soluble support, or when you want one nozzle reserved for the filled ESD grade so settings stay stable — the second nozzle's material is sealed off by a mechanical valve, with no wipe tower. Keep supports off functional surfaces, since they can affect measured resistance.

Applications

  • PCB nests, test and programming fixtures
  • Component trays, totes and feeder parts
  • Pick-and-place and conveyor parts on electronics lines
  • Housings for static-sensitive sensors and modules

Troubleshooting and tips

  • Reading too high. Raise nozzle temperature in small steps, check for a skin of support or brim, and re-measure.
  • Reading too low. Lower the nozzle temperature; conductive is not better for devices.
  • Inconsistent readings. Clean surfaces, condition parts at room humidity, and use the same probe and test voltage each time.
  • Brittle parts. Fillers cut elongation to a few percent; add fillets and avoid thin clips.

Available from MG World Tech: ABS ESD, 0.75 kg spool, $113.06. Order or request a quote →

Frequently asked questions

What surface resistance does ESD-safe filament need?

For most handling fixtures, the static-dissipative range: 1 × 10⁴ to below 1 × 10¹¹ Ω. Published printed values for ESD ABS grades fall between about 10⁴ and 10⁹ Ω.

What is the difference between antistatic and static dissipative?

Static dissipative is a resistance range. Antistatic describes low charge generation and does not guarantee a resistance value, so check the datasheet and measure the part.

Is a 3D printed ESD part compliant with ANSI/ESD S20.20?

S20.20 certifies an ESD control program, not a material. A printed fixture can be part of a compliant program once its resistance is measured and it is grounded as the program requires.

Why does my printed ESD part measure differently from the datasheet?

Datasheet values come from flat test plaques. Nozzle temperature, orientation, wall thickness and supports all change the result, so measure the actual part.

Related guides

Keep reading

All material guides →

Order ABS ESD or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote