Materials guide · Composites

Carbon-fiber polypropylene (PP-CF): properties and print settings

PP-CF is polypropylene filled with chopped carbon fiber. The fiber turns a soft, warp-prone plastic into a stiff, dimensionally stable one while keeping PP's low density and chemical resistance. Here is what to expect from it and how to print it.

$80.80 PP CF 18 · 0.70 kg spool · USD
Order / Request a quote

What carbon-fiber PP is — and when to choose it

Unfilled polypropylene is tough and chemically inert but floppy, and it shrinks hard as it crystallizes. Chopped carbon fiber — around 20% in published grades — restrains that shrinkage and multiplies stiffness several times over. The result is one of the lightest stiff composites you can print.

Choose PP-CF over carbon-fiber nylon when the part meets acids, bases, water or cleaning agents, or when you want a composite that needs essentially no drying. Choose nylon-CF when you need higher strength, better layer adhesion or more heat under load. Compared with ABS-CF, PP-CF is lighter and more chemical-resistant but harder to bond and glue.

Typical properties

PropertyTypical rangeTest method
Tensile strength (printed, XY)27–62 MPaISO 527 / ASTM D638
Tensile strength (printed, Z)6–15 MPaISO 527 / ASTM D638
Tensile modulus (XY)≈ 6–7 GPaISO 527 / ASTM D638
Elongation at break (XY)2–7%ISO 527 / ASTM D638
Heat deflection, 0.45 MPa (XY)135–160 °CISO 75 / ASTM D648
Density0.91–1.0 g/cm³ISO 1183 / ASTM D792

Typical published values across manufacturers, measured on test specimens; check your spool’s datasheet. Printed parts are usually weaker between layers (Z) than along them (XY).

Typical print settings

Nozzle temperature220–280 °C
Build plate40–95 °C on PP sheet, PP tape or PP adhesive
ChamberNot required by most makers; closed and warm helps big parts (Epitum: up to 90 °C)
Print speed20–55 mm/s
Part cooling0–50%
DryingUsually not needed; 65 °C · 4 h if exposed to humidity
NozzleHardened steel, ≥ 0.4 mm

Starting point compiled from manufacturers’ recommendations — fine-tune with the Printoformer material profile for your spool, nozzle and part geometry.

Start mid-range and adjust temperature for layer bonding: PP-CF's weakest direction is Z, so run the nozzle hot enough that layers fuse, and orient parts so the main load runs along the layers. The bed still needs a polypropylene-compatible surface — PP sheet, PP tape or a PP-specific adhesive.

Which Epitum: JL or L

The Epitum L suits PP-CF fixtures and housings: single material, a closed chamber heated up to 90 °C and a 360 × 360 × 610 mm volume for long parts. The Epitum JL is worth it when you want PP-CF in one nozzle and an unfilled material in the other. Both printers ship with wear-resistant nozzles, so composites need no nozzle swap. Expect moderate speeds, well below the 500 mm/s travel peak.

Applications

  • Automotive brackets, ducts and under-hood prototypes where weight counts
  • Fixtures, trays and clamps for chemical handling and plating lines
  • Low-pressure molds for silicone and urethane casting — PP's low surface energy aids release
  • Gluing and bonding clamps that adhesives will not stick to
  • Lightweight drone, robot and jig parts

Troubleshooting and tips

  • Use a hardened nozzle. Carbon fiber wears brass quickly; widening orifices show up as over-extrusion and stringing.
  • Read HDT carefully. Flat-printed (XY) heat deflection at 0.45 MPa is high, but values at 1.8 MPa and in other orientations are much lower — test the part under its real load.
  • Layers split. Raise nozzle temperature, reduce part cooling and print thicker walls.
  • Part welded to the PP sheet. Lower the bed temperature or switch to tape for small parts.
  • Plan joints without glue. Like plain PP, PP-CF bonds poorly with most adhesives. Design in screws, threaded inserts, snap-fits or clamps, and check the assembly method before the part is finalized.

Available from MG World Tech: PP CF 18, 0.70 kg spool, $80.80. Order or request a quote →

Frequently asked questions

Does carbon fiber polypropylene warp?

Much less than unfilled PP — the fibers restrain crystallization shrinkage. Several makers print it without a heated chamber, though large flat parts still benefit from a closed, warm build space.

Do you need a hardened nozzle for PP-CF?

Yes. Carbon fiber is abrasive; use hardened steel or another wear-resistant nozzle of 0.4 mm or larger.

What bed surface works for carbon-fiber PP?

The same as for plain PP: a polypropylene sheet, PP packing tape, or a PP-specific adhesive. Glass and bare PEI rarely hold it.

Is PP-CF stronger than nylon carbon fiber?

Usually not in strength or heat under load; PA-CF wins there. PP-CF wins on density, chemical resistance and moisture insensitivity.

Related guides

Keep reading

All material guides →

Order PP CF 18 or ask an engineer

Tell us about the part — we will confirm the material, settings and the right Epitum printer, and send a quote.

Request a quote